Name of Symposia: S03 - Injection Molding & Molds |
S03-657 Keynote
|
Determination Of Diameter, Length And Three-Dimensional Distribution Of Fibres In Short Glass-Fibre Reinforced Injection Moulded Parts Using µ-X-Ray Computed Tomography Salaberger Dietmar , Kastner Johann , Zitzenbacher Gernot , Stadlbauer Wolfgang , Freytag Rotraud
|
S03-645 Keynote
|
Application Of Ultrasonic Wave To Injection Molding Sato Atsushi , Ito Hiroshi , Koyama Kiyohito
|
S03-1180 Keynote
|
Multi-Component Injection Moulding - Heat Transfer, Thermal Extension And Bonding Strength Kuehnert Ines , Schuck Marcus , Feulner Robert W. , Schmachtenberg Ernst , Thornagel Marco
|
S03-184 Oral
|
Behaviour Of A Suspension Crystallization Model In Tube Flow Tanner Roger I
|
S03-319 Oral
|
Mold Surface Roughness And Cavity Filling Of Micro-Injection Molding Lam Yee Cheong , Ong Nan Shing , Zhang Hong-Lin
|
S03-484 Oral
|
Integrated Numerical Simulations To Predict Birefringence Of Injection Molded Parts Chang Yuan-Jung , Yang Wen-Hsien , Hsu Chia-Hsiang , Chang Rong-Yeu
|
S03-572 Oral
|
Water Assisted Injection Moulding: Simulations And Experimental Results From An Instrumented Process. Mulvaney-Johnson Leigh , Polynkin Andrey , Bai Luolin , Pittman John F T , Sienz Johann , Brown Elaine C , Coates Phil D , Brookshaw Brian , Vinning Kamal , Butler Jon
|
S03-598 Oral
|
Development Of Efficient Composite Systems For The Production Of Resin Cast Moulding Blocks Pontes A J , Sousa C , Gomes C , Pouzada A S
|
S03-1310 Oral
|
Multiple Benefits From Rapid Temperature Cycle Injection Moulding Pittman John
|
S03-682 Oral
|
On The Relations Between The Surface Topography And Tactile Perception Of Injection-Moulded Textured Polymers Valverde Velasco Anna , Karlsson MariAnne , Boldizar Antal , Ignell Sofie , Westberg Henrik , Rigdahl Mikael
|
S03-825 Oral
|
Modeling Flow-Induced Crystallization In Injection Molding Custodio Frederico J.M.F. , Anderson Patrick D. , Cunha Antonio M. , Meijer Han E.H. , Peters Gerrit W.M.
|
S03-1015 Oral
|
Two Component Injection Moulding: Influence Of Process Parameters And Material Properties On The Adhesive Strength Of Plastic/Rubber Composites Thust Torsten , Giese Ulrich , Schuster Robert H.
|
S03-859 Oral
|
Effect Of Cooling Time On In-Mold Constrained Shrinkage Of Injection Molded Plastic Parts In Consideration Of Residual Stresses Azdast Taher , Behravesh Amir Hossein , Mazaheri Body Kiumars
|
S03-919 Oral
|
Visualization Analysis Of Generation Process Of Irregular Gloss Patterns Appeared On Hinge-Molded Sample MASUDA Norimichi , YOKOI Hidetoshi
|
S03-1024 Oral
|
Some Insights Into The Fundamentals Of Water Assisted Injection Moulding Polynkin Andrey , Bai Luolin , Pittman John FT , Sienz Johann
|
S03-832 Oral
|
Numerical And Experimental Investigation Of Long Glass Fiber Breakage In Hot Runner Systems Cellere Alessandro , Lucchetta Giovanni
|
S03-1029 Poster
|
Influence Of Injection Moulding Parameters On The Electrical Resistivity Of Polycarbonate Filled With Multi-Walled Carbon Nanotubes Villmow Tobias , Pegel Sven , Pötschke Petra , Wagenknecht Udo
|
S03-196 Poster
|
Study On The Molding Of Nanostructure Using Injection Molding Huang Chin-Kwang
|
S03-251 Poster
|
Improvement Of Part Surface Quality In Microcellular Injection Moulding Process Using Variable Mould Temperature Control Chang Jen An , Chen Shia Chung , Lin Yu Wan
|
S03-296 Poster
|
Properties Of Precision Injection Moulded Parts From A Multicavity Mould Jaruga Tomasz , Bociaga Elzbieta
|
S03-405 Poster
|
Improving Lifetime Of Becu Injection Mold Insert By Depositing With Ni-P-Ptfe Layer On Mold Surface Yang Sen-Yeu , Huang Tzu-Chien , Chen Yen-Hao , Huang Po-Hsun
|
S03-437 Poster
|
Experimental Analysis Of Materials For Rapid Prototyping Sercer Mladen , Raos Pero , Pilipovic Ana
|
S03-454 Poster
|
Pressure Distribution And Flow Analysis Of Stereolithography Mold In Injection Molding An Chao-Chyun , Chen Ren-Haw
|
S03-475 Poster
|
An Importance Of Input Data For Polymer Flow Simulations In Injection Molds Wilczyński Krzysztof , Zięba Szymon , Wilczyński Krzysztof J.
|
S03-163 Poster
|
Two Component Injection Moulding: An Interface Quality And Bond Strength Dilemma Islam Aminul , Hansen Hans
|
S03-500 Poster
|
Validating 3D Numerical Simulation Of Core Deflection Chou Ya-Yuen , Yang Wen-Hsien , Giacomin A. Jeffrey , Hade A. J.
|
S03-972 Poster
|
Transcription Of Negative And Positive Microlens Arrays Of Light Guide Plate In Injection Molding Kim Jong Sun , Ko Young-Bae , Min In Ki , Paek Seung-Ho , Kim Jong Deok , Yoon Kyung Hwan , Kim Dong Sung , Hwang Chul Jin
|
S03-628 Poster
|
Numerical Simulation And Experimental Study On The Temperature Behavior Of Pulsed Cooling Chiou Yan-Chen , Chen Shia-Chung , Tarng Shih-Hsien , Tsai T.P. , Yang Wen-Hsien
|
S03-941 Poster
|
A Study On The Surface Characteristics Of Injection Mold And Injection Molded Part Depending On Lgp-Mold Fabrication Methods HWANG Chul Jin , DO Young Soo , KIM Jong Sun , KO Young-Bae , KIM Jong Deok , YOON Kyung Hwan
|
S03-1035 Poster
|
Thermo-Reversible Dmdbs Phase Separation In Ipp Applied In Injection Molding Housmans Jan-Willem , Peters Gerrit W.M. , Meijer Han E.H.
|
S03-729 Poster
|
Development Of Alternative Process Technology For The Multi-Component Injection Moulding Potente Helmut , Schöppner Volker , Kleeschulte Rainer
|
S03-731 Poster
|
Structure Of Injection Moulded Parts From Multicavity Mould Jaruga Tomasz
|
S03-816 Poster
|
Co-Injection Moulding: Effects Of Process Parameters On The Skin/Core Distribution In A Model Mould Briatico Vangosa Francesco , Pavani Francesca , Onori Roberto , Pavan Andrea
|
S03-476 Poster
|
Simulations Of Filling Imbalance In Geometrically Balanced Runner Systems Wilczyński Krzysztof , Nastaj Andrzej , Wilczyński Krzysztof J.
|