Name of Symposia: G09 - Modeling and Simulation |
G09-K2 Keynote
|
Direct Numerical Simulations of Hard Particle Suspensions in Planar Elongational Flow Hwang W.R., Hulsen M.A., Kang S.H.
|
G09-K1 Keynote
|
Predicting Polymer Properties Directly from Processing Conditions Meijer H.E.H., Govaert L.E., Engels T.A.P.
|
G09-08 Oral
|
Simultaneous Determination of Thermal Conductivity, Thermal Diffusivity and Specific Heat of Polymers by the Hot Wire Technique Nues dos Santos W.
|
G09-16 Oral
|
Influence of pvT-Data Measured at High Cooling Rates on Injection Molding Simulation Results Lucyshyn T., Langecker G.R., Duretek I., Fischer K.
|
G09-15 Oral
|
Micro Cavity Filling Behavior Studies of 1mm Diameter Micro Gear Chen G., Zhao J., Yong J.
|
G09-14 Oral
|
Flow Distribution in Flat Spiral Mandrel Dies Goharpey F., Malekzadeh M., Foudazi R.
|
G09-13 Oral
|
Modeling for Design of a Polymer Process Filter Cox C.L., Cox A.C., Jenkins E.W., Mucha P.J.
|
G09-12 Oral
|
Analysis of Molding Process for Epoxy Resin Used for Electrical Insulator Kushizaki Y., Igarashi M., Tada K., Yamada T.
|
G09-11 Oral
|
Finite Elemente Simulation of the Curing Process of Epoxy Resins Woicke N., Eyerer P.
|
G09-18 Oral
|
The Numerical Analysis of Injection-Compression Molding of Thermosets Han S., Jin X.
|
G09-09 Oral
|
Importance of Pressure Dependence of Viscosity in Steady Non-isothermal Shearing Flows of Compressible and Incompressible Fluids Huilgol R.R., You Z.
|
G09-19 Oral
|
Optimization of Injection Molding Using Numerical Simulation with the Surrogate Model Approach Zhou J., Turng L.S.
|
G09-07 Oral
|
On the Resolution of Inverse Problems in Technological Processes for the Production of Polymer Nanocomposites Ivanov Y., Hadjikov L., Stoyanov V.
|
Not avalaible |
G09-06 Oral
|
Dynamic Monte Carlo in Hierarchical Modeling of Polymer Processing Dorgan J.R.
|
G09-05 Oral
|
Prediction of Optical Properties for Stretched Polymers Using Molecular Dynamics Method Miyazaki Y., Togawa Y., Masubuchi Y.
|
G09-04 Oral
|
Computational Study for the Prediction of Optical Properties of Polymer Tanaka T., Aoyagi T., Shirai H.
|
G09-03 Oral
|
Towards a Solid-State Constitutive Model for Polymer Products with Process-Induced Molecular Orientation Focatiis D.S.A.D., Buckley C.P.
|
G09-02 Oral
|
A Memory Efficient Singular Finite Element Method for Flow of Viscoelastic Fluids Iwata S., Mori H., Ando S., Takahashi Y., Aragaki T.
|
G09-01 Oral
|
Modeling of Short-Fiber Composite Strength Jin X.
|
G09-10 Oral
|
Numerical Simulation of Underfill Flow for Flip Chip in a IC Package Tanifuji S.I., Hashimoto T.
|
G09-28 Oral
|
Modelling the Melting Process in Reciprocating Screw Injection Moulding Machines Especially Considering the Transporting Effects after Screw Idle Time Zitzenbacher G.
|
G09-37 Oral
|
Study the Effect of Nozzle Geometry on Hydroentangling Water-Jet Breakup Wang C., Jin X., Wang Shanyuan
|
G09-36 Oral
|
Start up of Capillary Flow of Polytetrafluoroethylene (PTFE) Paste: Experiments and Simulations Mitsoulis E., Hatzikiriakos S.G., Ochoa I.
|
G09-35 Oral
|
Estimation of Stress Levels at the Diverging Exit of a Capillary Die Through the Use of PolyFlow Simulations Pol H.V., Lele A.K., Joshi Y.M., Tapadia P.S.
|
G09-34 Oral
|
Experimental and Numerical Simulation of Melting and Sintering of a Polymer Powder Bed on a Heated Plate: Application to the Rotational Moulding Process Boutaous M., Crespy C., Purot E., Chantrenne P., Maazouz A., Bourgin P.
|
G09-33 Oral
|
Mesh Immersion Technique for 3D Moving Domain Calculation and Applications to Twin-screw Extrusion and Mixing Valette R., Vergnes B., Coupez T.
|
G09-32 Oral
|
Modeling of Mixing of Non-Newtonian Two Phases Flow in Co-rotating Twin Screw Extruders Sarhangi Fard A., Famili M.H.N
|
G09-31 Oral
|
Numerical Evaluation of Mixing in the Intermeshing and Translating Regions of Co-rotating Fully Conjugated Twin Screw Extruder Salami Hosseini M., Nazokdast H., Sharif F.
|
G09-17 Oral
|
Modeling and Simulation on the Morphological Evolution in Complex Flow Field Yu W., Zhou C.
|
G09-29 Oral
|
Temperature development of wall-slipping melts Timmermann K., Potente H., Kurte-Jardin M., Klus S.
|
G09-38 Oral
|
Simulation of Elongational Flow in a Cylinderical Converging Extrusion Tube Die Yousefi A.A., Daramizadeh A.
|
G09-27 Oral
|
Combination Model of Dispersed and Compacted Solids Melting Potente H., Pape J., Anger K.
|
G09-26 Oral
|
Numerical Simulation of the Extrusion Process and Die Design for an Industrial Profile, Using the Multi-mode Pom-pom Model Debbaut B., Dozolme A., Yukawa H., Marchal T.
|
G09-25 Oral
|
Dynamics and Stability of Nonisothermal Film Casting Process Using 2-D Phan-Thien and Tanner (PTT) Model Shin D.M., Lee J.S., Yoon J.H., Jung H.W., Hyun J.C.
|
G09-24 Oral
|
Application of Variational Principles in Modeling of Film Blowing Process for Non-newtonian Fluids Zatloukal M., Mavridis H., Vlcek J.
|
G09-23 Oral
|
Nonlinear Dynamics of Film Blowing Process: Multiplicity, Bifurcation and the Transient Solutions Hyun J.C., Shin D.M., Lee J.S., Jung H.W.
|
G09-22 Oral
|
Quick Time Behavior of Viscoelastic Liquid in Planar Flow Described by the Leonov Model Kwon Y., Lee S.W.
|
G09-21 Oral
|
Design of the Die Land for Cross Head Dies with Asymmetric Cross Section Mehranpour M., Gharaee R., Amyari A., Nazokdast H.
|
G09-20 Oral
|
Multifluid Flows, Interface Capturing and Application to the Simulation of the Water Assisted Injection Molding Process Coupez T., Rodriguez-Villa A., Silva L., Zerguine W.
|
G09-30 Oral
|
Modeling of the Mixing Process in Internal Mixer: the Case of The Case of Miscible Having Very Different Viscosities Adragna L., Jallut C., Couenne F., Cassagnau P.
|