Name of Symposia: G08 - Injection Molding and Molds |
G08-K2 Keynote
|
Numerical Simulation of Ear-flow: The Faster Advance of the Flow Front at the Edge of a Cavity Costa F., Yokoi H., Murata Y., Kennedy P.
|
G08-K1 Keynote
|
Water Assisted Injection Molded Glass Fiber Reinforced Nylon-6 Composites Liu S.J., Shih C.C., Wu Y.C.
|
G08-14 Oral
|
Injection Molding of Zirconia(ZrO2) Powder Considered Sintering Shrinkage Kwak T.S., Shin H.Y., Lim J.I., Lee Y.J.
|
G08-01 Oral
|
Residual Wall Thickness Distribution at the Transition and Curve Sections of Water Assisted Injection Molded Tubes Liu S.J., Hsieh M.H.
|
G08-02 Oral
|
Advances in Gas- and Water Injection Technique Michaeli W., Lettowsky C., Grönlund O.
|
G08-03 Oral
|
Mechanical Properties of Co-Injection Molded PPS Yamada K., Yukimune A., Yoshida T.
|
G08-04 Oral
|
Effects of Polymer Structure and Sintering Kinetics on Final Parts Properties in Rotational Molding Maazouz A., Perot E.
|
G08-05 Oral
|
Three Dimensional Simulation of the Elbow Flow of Bingham Fluids You Z., Huilgol R.R.
|
G08-06 Oral
|
Analysis on Shrinkage Error Compensation in Injection Molding of Aspheric Plastic Lens Chen C.C.A., Tzeng S.L., Kao S.C.
|
G08-07 Oral
|
3D Numerical Simulation of Micro Injection Molding Yang W.H., Chang D., Yang V., Chang P.C., Hwang S.J.
|
G08-08 Oral
|
True 3D and Fully Transient Mold Temperature Simulation of a Rapid Heat Cycle Molding Process Chen Y.F., Yang V., Yang W.H., Chang R.Y.
|
G08-09 Oral
|
Three-Dimensional Numerical Analysis of Weld-Line Strength for Injection-Molded Plastic Parts Peng A.Y., Yang W.H., Hsu D.C., Chang R.Y.
|
G08-10 Oral
|
A Design Support System for Plastic Injection Molds Fischer K., Lucyshyn T., Langecker G.R.
|
G08-11 Oral
|
Anisotropic Thermal Conduction in Injection Molding Zheng R., Kennedy P.
|
G08-13 Oral
|
Residual Stresses in Injection Molded Thermoplastic Parts Kim S., Kim C., Oh H., Youn J.R.
|
G08-28 Oral
|
Improvement of the Mold Releasing Properties by DLS Surface Modification for the Injection Processing Tsuchiya F., Suzuki H., Nakamura M.
|
G08-15 Oral
|
Detection of Surface Structure and Appearance of Injection Molded Parts. Berger G.R., Gruber D.P., Friesenbichler W., Langecker G.R.
|
G08-16 Oral
|
Quantitative Evaluation of Plastics Surface Appearance Aspects in Accordance with the Human Perception Gruber D.P., Berger G.R.
|
G08-17 Oral
|
Rapid Mold Surface Temperature Controls and Their Effects on the Injection Molded Parts' Qualities Chen S.C., Chang J.A., Jong W.R., Cin C.J.
|
G08-18 Oral
|
Measurement of Melt Temperature in Ultra-high-speed Filling Process by High-response Infrared Thermometer Hasegawa S., Yokoi H.
|
G08-19 Oral
|
Temperature Profiles of Ethylene Vinyl Acetate during Injection Moulding Alothman O.Y., Day R.J.
|
G08-20 Oral
|
Specifics in Injection Molding of Thermal Conducitiv Polymers for Mechatronic Applications Amesoeder S., Ehrenstein G.W.
|
Not avalaible |
G08-21 Oral
|
A Study on Influence of Resin Temperature and Material Kind on Filling Balance of Multi-cavity Molds with H-shaped Runner Chen J., Kanetoh Y., Yokoi H.
|
G08-22 Oral
|
Process Energy Measurements for Detailed Process Evaluations Dawson A.J., Rajamani H.S., Kelly A.L., Mulvaney-Johnson L., Coates P.D.
|
G08-23 Oral
|
Precise Molding Process by Inducing Sink Mark Ueda K., Watanabe J., Sawada K., Sugimoto Y., Yamanaka Y., Koseko H.
|
G08-25 Oral
|
The Effects of Annealing on the Deformation and Fracture Behavior of Injection Molded PLA Goto K., Nakano S., Kuriyama T.
|
G08-26 Oral
|
Interfacial Shear Strength in GF/PP Injection Molded Composites Yamada K., Yoshida T., Okumura H., Kotaki M., Hiroyuki H.
|
G08-27 Oral
|
Factors Affecting Beta-Crystal Morphology in Polypropylene During Injection Molding Process Kerddonfag N., Chinsirikul W., Rungseesantivanon W.
|
G08-12 Oral
|
Pressure Distributions in the Cavity in Injection Molding for Various Operational Conditions Lyu M.Y., Kim J.M., Nah C., Hwang H.S., Lee J.W., Lee S.H.
|