Name of Symposia: S10 - INJECTION MOLDING |
S10-311 Oral
|
Design Sensitivity Analysis Applied to Injection Molding Process: Injection Pressure and Multi-Gate Location Optimization Kalonji K. Kabanemi, Jean-François Hétu, Abdessalem Derdouri
|
Not avalaible |
S10-79 Oral
|
Iterative learning control and its application to injection molding process Yi Yang, Cheng Shao, Furong Gao Yi Yang, Cheng Shao, Furong Gao
|
Not avalaible |
S10-64 Oral
|
Design of Experiments to Optimize theWeldline Strength in Injection Molded Parts Shih-Jung Liu, Jun-Yu Wu, Jer-Haur Chang
|
Not avalaible |
S10-296 Oral
|
Development and Properties of Bi-Composite Mouldings Rui Sousa, Rui Reis, António Cunha, Michael Bevis
|
Not avalaible |
S10-325 Oral
|
Effect of Oil Additives and Injection Molding Process Parameters on the Tensile and Impact Energy of Polypropylene Gregory. A. Campbell, Sara E. Campbell, Matthew Bullwinkel, Joseph Savoka, Lona Ragona
|
Not avalaible |
S10-106 Oral
|
Improved product development tools for the in-mold film decoration process Martin Wielpuetz, Walter Michaeli
|
Not avalaible |
S10-42 Oral
|
On-Line Monitoring of the Injection Moulding Process by Dielectric Spectroscopy J. Guillet, J.M. Gonnet, I. Sirakov, R. Fulchiron, G. Seytre
|
Not avalaible |
S10-413 Oral
|
Important Considerations In Injection Molding Simulation M. R. Kamal
|
Not avalaible |
S10-213 Oral
|
Morphology and structure development in iPP articles moulded through non-conventional GAIM processes Rui M. Magalhaes, G.F. Smith
|
Not avalaible |
S10-142 Oral
|
Polyamide 6,6 Degradation During Injection Moulding Yves Bereaux, Laurent Barré, Didier Graebling
|
Not avalaible |
S10-93 Oral
|
Simulation Based Optimization of Injection Molding Bingfeng Fan, David Kazmer, David Hatch
|
Not avalaible |
S10-231 Oral
|
Corner deformation induced by shrinkage anisotropy of injected thermoplastics: Experimental study and numerical approach Amine Ammar, Vito Leo, Gilles Regnier
|
Not avalaible |
S10-156 Oral
|
Numerical Study of Residual Stresses and Birefringence in Injection Molded Parts Young Bok Lee, Tai Hun Kwon
|
Not avalaible |
S10-183 Oral
|
Measurement of residual stresses in thermoplastic moulded parts Thomas Giroud, Michel Vincent
|
Not avalaible |
S10-259 Oral
|
Analysis of In-mold Contact Conditions in Gas-assisted Injection Molding by Ultrasonic Image Scanner Hidetoshi Yokoi, Manabu Kawamura, Takeshi Watanabe, Susumu Nishiuchi
|
Not avalaible |
S10-238 Oral
|
Modeling and Simulation of the Injection–Compression Molding Process for Thin-Wall Parts Th. Hofer, H.G. Fritz
|
Not avalaible |
S10-407 Oral
|
Vacuum Pultrusion – A Process for Manufacturing Large Cross-section Profiles J.M. Methven, S.F. Bush, A.J. Hulme
|
Not avalaible |
S10-320 Oral
|
Ultrasonic measurements in the nozzle and cavity during polymer injection moulding E.C. Brown, A.J. Dawson, P. D. Coates
|
Not avalaible |
S10-300 Oral
|
Co-injection of glass reinforced polypropylene: Effect of rheology and molding conditions Abdessalem Derdouri, Djebbar Ait Messaoud, Bernard Sanschagrin
|
Not avalaible |
S10-376 Oral
|
A. Garcia-Rejon, M. Carmel N. Jivraj, K. Sehanobish, R. Ramanathan, A. Garcia-Rejon, M. Carmel
|
Not avalaible |
S10-375 Oral
|
Dr. Michael Thielen, SIG Plastics International, Troisdorf, Germany Dr. Michael Thielen, Frank Schüller
|
Not avalaible |
S10-225 Oral
|
Y. Douken Y. Douken
|
Not avalaible |
S10-350 Oral
|
F. Montezin, B. Monasse,D. Gille F. Montezin, B. Monasse, D. Gille
|
Not avalaible |
S10-188 Oral
|
Investigations on thermoforming of PET M. Keuerleber, B. Hegemann, A. Kech, P. Eyerer
|
Not avalaible |
S10-221 Oral
|
S. Tanifuji S. Tanifuji
|
Not avalaible |
S10-374 Oral
|
Current Challenges for Improved Optimization and Control of Thermoforming Processes H.F. Nied
|
Not avalaible |
S10-86 Oral
|
Calculation of Injection Molds and Molded Parts Andreas Franz, Walter Michaeli
|
Not avalaible |
S10-393 Oral
|
Optimization of cooling circuits in injection molds Warren Reynolds, Andrew N. Hrymak, M.A. Elbestawi
|
Not avalaible |
S10-121 Oral
|
Computational Simulation of the Injection Molding Process Using Quiescent Crystallization Kinetics Ricardo Bonon, Rosario Bretas
|
Not avalaible |
S10-285 Oral
|
Relevance of mould geometry on gate freeze-off time F. De Santis, R. Pantani, G. Titomanlio
|
Not avalaible |
S10-283 Oral
|
The influence of the cooling time of the injection moulded parts on PVT behaviour Beata Kowalska, Robert Sikora
|
Not avalaible |
S10-282 Oral
|
Measurement of flow birefringence in the slit die and comparison with the shear-stress in injection molding Tadaoki Okumoto, Mitsuru Nagasawa
|
Not avalaible |
S10-266 Oral
|
Interface Geometry of Simultaneous Composite Injection Molding Process by Numerical Analysis Koichi Emori, Atsushi Yokoyama
|
Not avalaible |
S10-228 Oral
|
Optimum design technique for injection molding Atsushi Yokoyama, Shinichi Yamane
|
Not avalaible |
S10-200 Oral
|
Study of break through phenomenon in sandwich injection molding Daisuke Watanabe, Hiroyuki Hamada, Kiyotaka Tomari
|
Not avalaible |
S10-127 Oral
|
Serge Monteix, F. Schmidt, Y. Le Maoult, G. Denis, M. Vigny Ecole des Mines d’Albi-Carmaux Campus Jarlard, Route de Teillet, 81013 ALBI CT Cedex 09 Serge Monteix, F. Schmidt, Y. Le Maoult, G. Denis, M. Vigny
|
Not avalaible |
S10-405 Oral
|
The analysis of applying injection compression molding to the manufacturing of a light guide Cheng-Hsien Wu, Yi-Li Su, Li-Nuan Tsai, T. James Wang
|
Not avalaible |